How To Install A Motherboard

How To Install A Motherboard

Installing a motherboard is one of the most important tasks for any computer build. It’s also one of the more difficult jobs to do correctly, which is why you should follow this guide on how to install a motherboard.

This article will teach you all about what type of motherboard you need for your system and how to install it in your case.

Before Getting Started

Before you unbox the motherboard, make sure your workspace is free of any dust or debris.

The mechanical components are sensitive to particles in their environment so cleanliness will help ensure a smooth process!

Next, gather your tools – Another likely obvious tip for seasoned individuals is to make sure you have all of the necessary equipment.

You’ll want to make sure your power supply isn’t connected and that the ESD bands or mats protect you from static electricity.

Recommended read: How Are Motherboards Made ?

Some seasoned users say they never had an issue, but we’re all cautious with safety risks around electronics where there can be a chance for shorting out parts if oils get on them while working in tight spaces like under desks at work!

Some people feel safer using rubber gloves than wearing nothing as powdery substances may cause damage depending upon what kind of glove one wears;

Additionally it prevents any potential environmental issues caused by oils/petroleum products transferred into contact during handling.

One last thing that we would like to tell you before you install your motherboard is the different types of motherboards that are available in the market:

Steps To Install A Motherboard

1. Unpack the board

After you open the box for your new PC, there will be plenty of cables and other components.

Take everything out but one thing-the metal plate with holes cut into it!

This is what we need later on in this guide so make sure to save it until then.”

The motherboard is now ready to go inside the anti-static bag.

Slide it out of its protective covering, and place on top with an additional layer or two in between for extra safety precautions.

A metal blanking plate will need replacing before installation onto any system board which must be done carefully so as not damage anything else components beneath!

2. Measure blanking plate

You will only have access to the ports that your motherboard has with a blanking plate.

Some motherboards use generic plates, so you may need remove metal covers before being able connect them in order for everything work properly.

Always make sure you have the right blanking plate before cutting out your ports, and always double check which way is facing up.

It’s important because this will only fit one way so if it’s not lined up correctly there won’t be any room for expansion!

3. Remove unnecessary bits

If you want to remove any metal from your case, it’s time for some serious cracking. You have two options here:

First is by pulling on the piece with force and hoping that one side pops off;

Second would be rocking them gently until all cracks evenly apart into different pieces like toothpaste being squeezed out of tube!

Some ports may be covered by a flap. In this case the edge of your motherboard needs to go in between two sheets of plastic so make sure you bend it far enough for everything and give yourself adequate room!

4. Install the blanking plate

From the inside of your computer case, you need to take out a piece called “blanking plate”.

Align it with what was measured against yourself and push into gap at rear where there are two metal tabs sticking up on both sides ( these will fit in between).
Remember: same orientation!

The ridge around the outside of a plate should clip into place and remain stable without any support.

5. Measure where the motherboard goes

Next, you need to see where the screw holes for your motherboard will go.

Lie down on a flat surface and make sure that all internal cables are out of the way before carefully sliding in an away any foam pads holding up this component.

Once everything has been removed from behind it or if there isn’t any then simply slide them gently into their designated spots against one another with rear ports pushed firmly upward as they’re meant too without much effort-it can even happen automatically!

6. Fit the risers

The hole-laden risers need to be screwed into place with the copper screws that come included.

These will allow for proper grounding and safety, as well preventing shorting out if there are any touching metal plates when installed correctly.

Installing these is easy: just make sure you use all of your allotted space by using them equally between top and bottom Motherboard mounting holes!

7. Slide the motherboard into place

Reinsert the motherboard into its case, making sure to align all screw holes with risers underneath.

If some are missing and you don’t have ones that fit your board properly in place or they’re not long enough for when screwed down tightly on top of each other (which can cause pressure pushing against one another).

Then find an alternative way like putting them below where there isn’t much support so their weight doesn’t push too hard onto any specific points just yet-this will take more force but gives a better result without breaking anything!

8. Screw the motherboard down

Screwing in the motherboard is finished when you have screwed and secured all four sides of it.

Make sure that each screw goes into its designated hole, without breaking or bending any delicate parts on board!

Once you’ve done the corners, put screws in each of these other holes to prevent any movement.

As long as your installation looks good and doesn’t move around too much when faced up against something solid on top like a bookshelf or dresser for example; then this should do the trick!

9. Identify ATX connectors

With the motherboard in place, you’re ready to connect it with power.

There are two connectors that need connecting – an ATX and 24 pin connector on modern motherboards but older boards require only a 20 pin one so make sure this is connected before putting away your tools!

10. Plug in the ATX connector

That’s right, you need a 24-pin connector in order for your computer to power up.

This should be easy enough because most of them are located by IDE ports on the right side of the motherboard but sometimes they’re hidden underneath other things so keep looking!

The ATX connector is a snug fit, so you’ll need to be careful when lining up the pins.

Once they are correctly aligned and lined up with their clips on each side of an inserted cable (to hold them in place) give it one gentle tug before securing into place by pressing down lightly from above using both thumbs at once.

11. Identify secondary connector

Today’s motherboards have a secondary power connector. On most boards, this is a single four-pin connector that can provide up to 12V for the processor and other components in your computer – but some require an eight pin adaptor (as shown above).

Check with you PSU manufacturer before buying anything!

This might be a good time to remind you that the eight-pin connector on power supplies can also split into two.

If your motherboard only has four pins, then it’s up to you which one of those will plug in – but make sure they’re both connected!

12. Connect secondary connector

Finding and installing the power cable for your machine is easy.

Simply locate the secondary motherboard connector, plug it in on one side of this piece so you can only have success when inserting into place (it won’t go crooked like other cables), then attach with ease from there!

It’s important to slide the connector gently into place as you want it in correctly.

You’ll need a bit of force, but don’t worry – once clicked together they won’t budge!

Final Words

So there you have it. Now you know how to install a motherboard! We hope this article was helpful. Thank you for reading the article.

ALSO READ

How To Check What Motherboard You Have?

What Socket Type Is Soldered To The Motherboard Along With The CPU?

How To Clean A Motherboard

How To Connect RGB Fans To Motherboard?

How To Tell If Motherboard Is Dead

Leave a Comment